Can I Install a Bath Tub Myself? Considerations And Actions
Can I Install a Bath Tub Myself? Considerations And Actions
Blog Article
Everybody may have their unique rationale when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a bathtub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and also in some cases, tiling abilities. Changing an old tub with a new one is additionally a moderately hard project. If the old bathtub is readily easily accessible, the task can move easily; if you have to open up a wall surface to eliminate the old bathtub as well as place the new tub, the task is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly require a helper to leave the old bathtub and embeded in the new one. Make certain you have actually qualified yourself for the task and also are comfortable trying it. Instead of working with a contractor to take over a halfway-completed job, it is much better to take into consideration using one prior to you begin. Chances are you may require a specialist plumber to make tube links.
This article will assist you set up a brand-new bath tub in your washroom if you have already purchased a new bathtub and also do not require to transform the arrangement of your previous water supply pipes.
Your tools and material checklist ought to make up the following:
Planning for the Installment
To start with, the supporting frame supplied with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets device to avoid strain on the bath tub.
Fit the adaptable tap connectors to the bottom of both faucets using 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its last setting.
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you should do is separate the supply of water. After doing so, turn on the faucets to drain any kind of water staying in the system. The process of getting rid of the existing taps can be fairly problematic as a result of the restricted access that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this process. Once the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any old securing substance.
Before proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, place the bathtub in the called for placement. The wood boards are handy in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four small points.
The next goal is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as readjusting the feet on the bath tub until the spirit level reads level.
To set up faucets, fit all-time low of the furthest adaptable tap port to the ideal supply pipe by making a compression join; after that do the same for the other faucet.
Switch on the supply of water and also check all joints and new pipework for leakages and also tighten them if necessary. Fill up the bath tub and likewise inspect the overflow outlet as well as the regular outlet for leakages.
Lastly, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the tub needs to wait until the tub has actually been used at least when as this will resolve it right into its final placement.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin guaranteeing that the washing machines are in location in between the faucet and the sink. Safeguard the tap in position with the producer provided backnut. When the tap is firmly in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet ports. The former kind ought to be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom meets the tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bathroom and also the tiling, resulting in difficulties with moisture and feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components as well as fittings. They are offered in tubes and also cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not take into consideration this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly available on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water-proof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen person who reads on How to Install a Bathtub Yourself, I imagined sharing that editorial was really useful. Are you aware of anybody else who is serious about the subject? Why not promote it. Thank you so much for going through it.
Schedule Appointment
Report this page